+86-173-0318-1768
Wear-resistant And Impact-resistant Rubber Linings for Screen Feeders
You are here: Home » Products » Rubber Liners » Feedbox Liner » Wear-resistant And Impact-resistant Rubber Linings for Screen Feeders

Product Category

Contact Us

WhatsApp: +86-173-0318-1768
Tel: +86-173-0318-1768
E-mail: 
Add: Wencheng Industrial Zone, Jing County, Hengshui City, Hebei Province
 

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
sharethis sharing button

Wear-resistant And Impact-resistant Rubber Linings for Screen Feeders

Strudex screen-feeder linings combine a resilient rubber contact face with a built-in steel plate. The two materials have different roles: the rubber takes mineral contact, while the steel forms part of the panel construction. This makes the complete section important when defining impact protection at the feed point.

  • Wear-resistant rubber working surface.
  • Built-in steel plate as part of the liner.
  • Selection around drop geometry, contact area and feeder support.

Describe where the material strikes and then slides. A section chosen for a concentrated rock drop needs a different review from a broad area exposed mainly to sliding abrasion.

Availability:
Quantity:

Strudex steel-backed rubber feedbox liners combine a wear-resistant rubber face with a built-in steel plate. The rubber is the working surface that receives the minerals. The plate forms part of the panel construction beneath that surface. Specifying both materials together helps distinguish a reinforced liner from a loose rubber sheet or a bare steel wear plate, without assuming a particular attachment method.

Technical Parameters

ParameterProduct specification
Product typeRubber lining for screen feeders
Wear-face materialWear-resistant rubber
ReinforcementBuilt-in steel plate
Application areaFeeder or feedbox material-contact surfaces
Handled materialMineral feed
Working dutyImpact and abrasive contact
Contact responseResilient rubber wear surface

Two materials, two different jobs

  • Rubber wear face. Separates the abrasive stream from the underlying metal and deforms under local particle contact. Available wear section, contact severity and the tendency for cutting or tearing as well as gradual abrasion.
  • Built-in steel plate. Provides the metal part of the liner assembly behind the rubber. The specified plate geometry and its relationship to the panel support and retention. The presence of steel does not by itself define bolts, welds or adhesive mounting.
  • Feeder or feedbox support. Carries the installed liner and the loads transferred through it. Sound supporting surfaces and the approved attachment arrangement. A reinforced panel cannot be treated as a repair for a cracked or distorted feeder.
  • Panel edges and junctions. Connect the separate sections into the protected material path. Coverage of the contact zone and an edge arrangement that does not create an exposed step or a route for abrasive material behind the lining.

The steel plate and rubber should be assessed as a complete liner, while the feeder structure remains a separate component. A panel that rests unevenly or moves at its attachment can develop a different local load from one seated as designed. Increasing the rubber thickness alone will not resolve an unsuitable support or an unidentified fixing arrangement.

Read the impact as a moving material stream

  • A direct drop concentrates energy around the landing region. Record the largest credible lump and the distance through which it falls to the contact surface. Average production tonnage describes the stream over time, but not the severity of an individual rock striking the liner.
  • A glancing transfer combines impact with sliding. The incoming material can retain speed from a belt or chute and scrape along the face after first contact. Show the direction and angle on the layout, because a wear track extending downstream needs coverage beyond the visible impact crater.
  • Steady operation and an empty restart can expose different surfaces. A material bed may cushion the arriving stream during continuous feed, while the first lumps after an interruption strike rubber directly. Include surges and feed interruptions when defining the contact duty.
  • Uneven feed can concentrate load across only part of the box width. A change in distribution may explain one heavily damaged panel beside several lightly worn ones. The replacement decision should address that contact pattern rather than assigning the same impact description to the entire box.

Balance the section against the passage

A thicker rubber section adds wear material but also occupies space in the feedbox. Check its effect on the passage into the screen and on transitions to side or discharge protection. The useful dimension is the complete installed section, including how it seats and meets adjacent panels. A proposed thickness should address a defined wear requirement while preserving the required material path.

Wear signatureMeaning for the next liner selection
Broad face thinningReview the abrasive duty and the remaining local wear allowance. Compare the original new section with the worn profile rather than measuring only the average surface.
Deep local cuts or torn rubberIdentify sharp material, oversize and direct impact at that location. More abrasion resistance alone does not describe the cutting duty.
Damage at a corner or jointCheck whether an edge projects into the stream, lacks support or permits material behind the liner. Edge geometry can govern the failure before the broad face is consumed.
Steel exposed at one locationAssess the affected panel and its support against the installed design. Intact backing does not mean the original resilient wear-face function remains available at the exposed point.

Rubber can dampen the ringing created by direct rock-on-metal contact. That material characteristic does not establish a fixed noise reduction or a site exposure limit. Similarly, a wear-resistant rubber description is not a temperature or chemical rating. Sharp tramp metal, unusual heat and specific chemicals need to be included in the material assessment alongside the normal mineral feed.

Specify the impact zone as a panel arrangement

  1. Mark the landing area and downstream sliding path on the feedbox layout. Show the complete outline, orientation and thickness of the required panels, together with the boundary to retained lining. This links the selected section to the actual area that needs protection.
  2. Define the supporting and retention interfaces on the drawing. Confirm whether dimensions describe the whole panel or only its rubber section, and identify the fastening scope separately. The internal steel plate is a construction fact, not permission to choose any convenient site fixing method.
  3. Evaluate replacement by local condition and geometry. Retain the part reference and installed profile, then compare later wear at the same locations. Replace a damaged interface or exposed wear section through the approved maintenance scope instead of using a universal thickness percentage.

Send Strudex the panel arrangement and a description of the rock contact, including trajectory, oversize and support details. The resulting requirement should define the rubber-and-steel section needed at each location, rather than rely only on the general terms high impact or heavy duty.

Product FAQ

Does the built-in steel plate determine how this feedbox liner is mounted?
No. The steel plate is part of the liner construction, while the mounting interface must be defined separately. Provide the existing support and fixing drawing. Do not assume a welded, bonded or bolted installation solely from the presence of steel inside the panel.
What information matters most for a liner directly beneath a large rock drop?
Describe the impact event, including the largest credible lump, drop height, direction of travel and frequency. Average throughput alone does not define that load. Show whether rocks strike rubber directly after an interruption or normally land on an established material bed.
Will a steel-backed rubber liner repair damage in the feeder structure?
No. The rubber wear face and internal steel plate protect the covered area from material contact; they do not establish that the supporting feeder is sound. Inspect cracks, distortion and worn mounting locations before replacement, and resolve structural repairs through the equipment maintenance process.
Can we keep using a panel after the rubber has worn through locally?
Local exposure needs a condition assessment before continued operation. Check the critical remaining section, the steel backing and nearby attachment areas against the installed design. Do not judge the panel only by its average rubber thickness or assume that intact backing provides the same wear protection.
Previous: 
Next: 
+86-173-0318-1768
Wencheng Industrial Zone, Jing County, Hengshui City, Hebei Province
Manufacturer of mill liners, rubber screen panels, flotation equipment accessories and other mineral processing wear-resistant spare parts.

Quick Links

Product Category

Contact Us
Copyright © 2024 Strudex Tech Co., Ltd. All Rights Reserved. Sitemap. Support by leadong.com. Privacy Policy.