+86-173-0318-1768
Pump Rubber Liner for Mining
You are here: Home » Products » Flotation Spare/Pump Spare Parts » Pump Rubber Liner » Pump Rubber Liner for Mining

Product Category

Contact Us

WhatsApp: +86-173-0318-1768
Tel: +86-173-0318-1768
E-mail: 
Add: Wencheng Industrial Zone, Jing County, Hengshui City, Hebei Province
 

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
sharethis sharing button

Pump Rubber Liner for Mining

Strudex rubber pump liners form the replaceable wear surface inside a mining slurry pump casing. The bolted construction provides mechanical attachment, while elastomer seal rings support the liner joints. This arrangement makes the liner, its sealing interfaces and the surrounding casing a connected replacement assembly.

  • Bolted attachment for liner removal and renewal.
  • Moulded elastomer construction for the slurry-contacting surface.
  • Joint and impeller checks for the selected pump configuration.

Specify the exact pump model and liner reference when ordering. Rubber and metal wet-end arrangements must be checked as a complete configuration, including their companion parts and clearances.

Availability:
Quantity:

Strudex bolted rubber pump liners provide a replaceable slurry-contacting surface inside the pump casing. Mechanical attachment holds the liner sections in position, while elastomer seal rings support the joints between them. This construction separates the renewable wear surface from the surrounding casing and makes the liner, seals and companion wet-end parts a coordinated assembly.

Technical Parameters

ParameterProduct configuration
ComponentReplaceable slurry-pump casing liner
Wear materialRubber / moulded elastomer
AttachmentBolted to the casing
Liner jointsSupported by elastomer seal rings
Related wet-end liner formsCover-plate and frame-plate configurations
Selected rubber-family dutySmall particles without sharp edges
Assembly referencePump-specific wet-end drawing
ApplicationMining and mineral-processing slurry pumps

A renewable surface inside a supported casing

The casing carries the assembly, while the internal rubber sections define part of the path seen by the slurry. The impeller supplies the pumping action; the liner remains stationary around that action. Keeping these roles distinct explains the value of a replaceable liner: worn internal surfaces can be renewed within a serviceable pump structure rather than treating each worn area as a new casing requirement.

ElementContribution to the assembly
Rubber wear surfaceForms the slurry-contacting profile. Its compound and geometry must suit particle contact and the liquid exposure while preserving the intended wet-end passage.
Casing supportCarries and locates the liner. Correct support matters because a moulded section needs the intended seating arrangement as well as the correct outside dimensions.
Bolted retentionMechanically secures the sections and permits their removal. The relevant bolt arrangement and tightening procedure belong to the selected pump design.
Joint sealsComplete the interface between mating sections. Correct seal references and undamaged contact faces are needed together; the rubber body alone is not the complete joint.

How the joint becomes part of the flow boundary

Liner joints must close in the arrangement intended by the pump. A displaced seal, trapped solid or damaged mating face can create a problem at the interface even when most of the liner has substantial material remaining. For that reason, leakage at a joint should be reviewed as an assembly condition rather than automatically attributed to general rubber wear.

  1. Identify the sections and the seal that belongs at each joint. Cover-side and frame-side parts may perform different roles, so preserve their references and orientation on the assembly drawing.
  2. Seat the sections against their intended support surfaces. Clean, serviceable mating regions allow the selected shapes to close without using fasteners to force a dimensional mismatch into place.
  3. Apply the pump’s tightening sequence and specified force. The objective is the intended assembled geometry; a universal torque taken from another size or metal-lined version is not an equivalent procedure.
  4. Check the complete wet end before returning to service. Retention, joint closure and impeller clearance address related but separate requirements, each defined by the selected pump arrangement.

Rubber responds to particles differently from metal

An elastomer wear surface can yield during particle contact, making material resilience part of its wear response. Strudex’s own rubber wet-parts catalogue identifies small particles without sharp edges as a relevant duty. This is a useful boundary: abrasion resistance in a fine slurry should not be read as immunity to a sharp fragment, intermittent oversize or mechanical contact.

  • For fine abrasive solids, describe size distribution, concentration and particle shape together. A single nominal slurry density does not show whether occasional cutting particles are present.
  • For chemical exposure, identify liquid constituents, concentrations and temperature. A compound that suits one process stream may not suit a cleaning liquid or oil contamination that reaches the same surfaces.
  • For damaged joints, examine seal condition, seating and casing support before changing the compound. Material substitution cannot restore a missing seal or correct a distorted retained interface.

Metal and rubber configurations are pump-specific choices

Some slurry pumps are designed to accept different wet-end material combinations within a common casing. That capability belongs to the particular pump and its approved parts arrangement. A rubber liner can also work with a metal impeller where the design permits it, but the combination must be specified through the complete wet-end drawing rather than inferred from nominal pump size.

Replacement situationWhat the choice must preserve
Like-for-like rubber renewalThe moulded profile, section interfaces, seals and the required impeller relationship. Identify which companion parts remain in service and whether their condition is suitable.
A proposed metal-to-rubber conversionThe full compatible combination, including any changed impeller, throat region, seals or other parts. A liner-only price does not establish the complete conversion scope.
Repeated cutting or unusual local lossThe actual solids range and hydraulic duty, not simply a harder or thicker replacement. Establish the cause before standardising another rubber specification.

For an order, connect the liner part number with the pump model, drawing revision, section position and required seals. Provide the current impeller material and the slurry duty so the proposed combination can be defined. A concise component schedule is more useful than an unsupported promise of universal interchangeability, and it gives the maintenance team a clear scope for renewing the pump’s internal wear surfaces.

Product FAQ

Why should the liner joint seals be identified with the liner sections?
The seals and mating liner faces work together to close each joint. Ordering a rubber section without its correct seal reference can leave the assembly incomplete or mismatched. Inspect retained seals, contact faces and casing supports during the overhaul, especially where the previous assembly showed leakage.
Can these rubber liners replace hard-metal liners without other changes?
Only if the particular pump design accepts that complete wet-end configuration. A material conversion may also involve the impeller, throat region, seals or clearances. Compare the relevant assembly drawings and list every changed and retained component before treating the order as a liner-only substitution.
Are rubber liners suitable when occasional sharp oversize reaches the pump?
That exposure needs specific review. Strudex’s rubber wet-parts family is described for small particles without sharp edges; intermittent coarse or sharp material can introduce cutting and tearing. Report the maximum credible solids and foreign-material history, rather than selecting rubber from the average particle size alone.
What should happen if a new liner will not seat in the casing?
Stop and check orientation, part revision, retained components, trapped material and the condition of the supporting surfaces. Do not force, trim or drill the liner as a routine fitting step. Resolve the discrepancy against the approved assembly drawing before tightening the casing and liner arrangement.
Previous: 
Next: 
+86-173-0318-1768
Wencheng Industrial Zone, Jing County, Hengshui City, Hebei Province
Manufacturer of mill liners, rubber screen panels, flotation equipment accessories and other mineral processing wear-resistant spare parts.

Quick Links

Product Category

Contact Us
Copyright © 2024 Strudex Tech Co., Ltd. All Rights Reserved. Sitemap. Support by leadong.com. Privacy Policy.