+86-173-0318-1768
Quick-change, Impact-resistant Rubber Liner for Screen Feeders
You are here: Home » Products » Rubber Liners » Feedbox Liner » Quick-change, Impact-resistant Rubber Liner for Screen Feeders

Product Category

Contact Us

WhatsApp: +86-173-0318-1768
Tel: +86-173-0318-1768
E-mail: 
Add: Wencheng Industrial Zone, Jing County, Hengshui City, Hebei Province
 

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
sharethis sharing button

Quick-change, Impact-resistant Rubber Liner for Screen Feeders

This Strudex feeder liner uses 60 Shore A natural rubber and offers bolted installation. The rubber face receives mineral contact, while the fixing and support arrangement keep the panel in its intended position. Hardness, wear thickness and bolt geometry each describe a different part of the selection.

  • Natural rubber with nominal 60 Shore A hardness.
  • Bolted mounting option for a defined mechanical connection.
  • Custom liner dimensions for the specified feeder requirement.

Select the complete panel around the feed contact and installation interface. A matching hardness number or hole pattern alone is not a complete replacement specification.

Availability:
Quantity:

Strudex 60 Shore A natural rubber feeder liners provide a resilient contact surface where minerals strike and slide through the feeding area. The bolted option gives the panel a defined mechanical retention interface. The product combines a stated material hardness with a shaped wear component; neither property should be separated from the support and the contact duty when selecting a replacement.

Technical Parameters

ParameterProduct specification
Product typeRubber feeder liner
Rubber materialNatural rubber
Nominal hardness60 Shore A
Mounting optionBolted installation
Equipment applicationScreen feeders
Working exposureMineral impact and wear
Custom configurationDimensions to the agreed feeder requirement

What 60 Shore A describes

Shore A hardness describes resistance to indentation. It is useful for identifying the nominal firmness of the natural rubber, but it does not describe the complete compound or predict service life. Abrasion, tearing and repeated deformation impose different demands. The published 60 Shore A value belongs to this feeder-liner description; it is not a rule for every Strudex lining or an instruction to substitute any rubber of the same hardness.

Selection dimensionWhat it contributesWhy the other dimensions still matter
Natural rubber materialA resilient working surface that can deform and recover during particle contact.The actual formulation and exposure govern suitability; oil, chemicals, temperature and cutting contaminants need their own assessment.
Nominal 60 Shore A hardnessAn identified indentation-hardness specification for the rubber.It does not define abrasion loss, tear strength, allowable impact or the geometry that controls how the panel is supported.
Rubber wear thicknessMaterial between the incoming stream and the protected structure.Extra thickness changes the installed envelope and can affect the passage or the level of adjoining sections.
Bolted retentionA mechanical means of locating and holding the selected panel.Correct seating, fastening details and support are necessary; a bolt pattern alone does not establish a compatible assembled connection.

The rubber and the bolt joint perform different work

  • The rubber face receives the material contact. Its section and support influence how it deforms under that contact. A panel with a void or uneven seat beneath it can experience local movement that differs from the intended supported condition.
  • The fastening arrangement holds the component at its designed interfaces. Bolt seating, washers or other specified elements, and the contact surfaces must follow the selected assembly. Their dimensions and tightening method cannot be inferred solely from a nominal thread size.
  • Rubber compression is part of the joint behavior where the approved fixing bears through rubber. Forcing a fixing tighter is not a substitute for an identified seating detail. Follow the specified assembly method rather than using the feel of the connection as an acceptance criterion.
  • The hole region and the broad wear face can reach different limits. A panel may retain substantial face thickness while an attachment area is torn or distorted. Conversely, a sound fixing does not establish adequate wear material beneath the landing point. Evaluate those regions separately.

Choose the section around the moving feed

A feeder lining can experience direct impact at first contact and sliding abrasion farther along the same panel. The shape of the wear track shows where those duties occur. A crater beneath the incoming stream, long scratches downstream and damage at an edge indicate different contact conditions. Use that distinction to define rubber thickness and coverage instead of applying the same wear allowance everywhere by default.

Operating conditionEffect on the panel review
Large or sharp mineral fragmentsInclude the maximum credible size and shape, not only the average feed. Cutting and tearing require a different review from gradual rubbing wear.
A stream arriving at an angleShow the landing point and sliding direction. The liner needs coverage along the contact path, including the junction with the next section.
Surges or an empty restartRecord whether the first lumps hit rubber directly before a material bed develops. Average steady-state tonnage may not describe that event.
Material caught behind a panelInspect edge support, seating and retention. Increasing hardness will not close an unidentified route behind the lining or restore a damaged support.

The custom outline should fit the working space as well as the mounting locations. Preserve the intended feeder passage, keep adjoining edges coordinated and allow access to the specified fixings. A thicker replacement should be checked against the new installed arrangement, not assumed to fit because a thinner worn part can still be removed through the available opening.

Define a bolted replacement that can be assembled correctly

  1. Record the complete new-panel dimensions and orientation, together with hole centers, seating geometry and the supporting surface. Distinguish a worn sample measurement from the intended original size. Feed direction is important when shaped edges or unequal sections are present.
  2. Identify the required fastener assembly and its access before the shutdown. A bolted arrangement can be accessible from one side or require work at both sides; the selected drawing determines the task. Confirm separately whether the order includes only liners or also the specified hardware.
  3. During isolated replacement, inspect the exposed seat and mounting locations before fitting the new rubber. A damaged hole, distorted support or trapped abrasive material changes the connection. Resolve that condition rather than forcing the replacement into place.
  4. After assembly, verify seating and the required fastening checks through the equipment procedure. Retain the panel reference and installed section as the baseline for wear. This makes subsequent replacement decisions about the actual wear face and joint, rather than the hardness number alone.

For a Strudex enquiry, state the 60 Shore A natural-rubber requirement alongside the component drawing and feed duty. That combination defines the intended product more clearly than the terms quick change or impact resistant by themselves.

Product FAQ

Is 60 Shore A enough information to identify a replacement feeder liner?
No. It identifies nominal hardness, rather than the complete compound or panel design. Retain the natural-rubber description with the drawing, part reference and mounting details. Matching hardness alone does not establish equal abrasion behavior, tear resistance or fit in the existing feeder.
Does the quick-change description mean this liner uses a snap-on system?
No. This product identifies bolted installation as an option. The replacement task depends on the approved fixing arrangement, access and condition of the old hardware. Confirm the actual bolt layout rather than assuming that the product name implies a separate tool-free connection.
What should we measure when matching the existing bolt pattern?
Record hole centers, panel thickness, seating details and access to the opposite side of each fixing. Include the panel orientation and feed direction on the sketch. Check the feeder itself for altered or damaged mounting locations instead of measuring only the removed rubber.
Can the existing bolts and washers be reused during a panel change?
Reuse depends on the specified assembly and the condition criteria in the equipment procedure. Inspect the fasteners and seating surfaces during removal, and identify the required hardware before the shutdown. A new rubber panel does not compensate for a damaged or unsuitable fixing arrangement.
Previous: 
Next: 
+86-173-0318-1768
Wencheng Industrial Zone, Jing County, Hengshui City, Hebei Province
Manufacturer of mill liners, rubber screen panels, flotation equipment accessories and other mineral processing wear-resistant spare parts.

Quick Links

Product Category

Contact Us
Copyright © 2024 Strudex Tech Co., Ltd. All Rights Reserved. Sitemap. Support by leadong.com. Privacy Policy.